Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi Everyone,
I’ve implemented a ST7735S on the NRF52832 using the GFX example. My problem is that I can’t seem to update the screen in such a way that the screen doesn’t...
Hello,
I am trying to make LSM6DSR (STEVAL-MKI194V1) work with nRF52840 using TWI Communication.
Problem:
Firstly, I modified the TWI sensor example to use the accelerometer...
Hi guys, I've got a nRF 52840-DK, I want to verify the new features like 2M/long range/advertising extension.
1. Is there any exmaple to test these featues, or any guideline...
Hello,
On the nRF52840, is it possible to switch from TXIDLE to RXIDLE or from RXIDLE to TXIDLE without going first back to DISABLED ?
We are using the radio in 1 Mbps...
To the kind attention of Nordic support team,
we are very much interested in interacting with your nRF52840 devices preprogrammed with the wireless bootloader and waiting...
Hi! We are currently trying to develop a low power framework for our nRF52840 DK with SoftDevice S140. After disabling various peripherals and interrupts we use the provided...
Hello Team,
I just recently purchased Thingy52 i was wondering i can use NFC NDEF update using python library if it is possible can you point me to right
documentation...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
