after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I am evaluating two nRF52832 boards with a PCA10040. I am using the SDK examples Central and Peripheral to talk to each other on Tera Term. I am using the "send file"...
Hi,
We have implemented the reference design of the NRF24L01+. Our tests results in a low range (about 6 meters), we excepted a multiple of that (about 1 kilometer).
I...
We have connected a 50 Ohm Antenna with NRF52832-QFAA-R7, but we tested and found the antenna signal is weak. Could anyone help to provide some proposals for how to improve...
Hi,
I have a STM32 MCU and I want to flash this MCU by using an nRF52840. The two chips will be connected by UART.
From where I need to start, and what is the most easiest...
When attempting to connect to an MQTT broker set up on my local machine using the mqtt simple sample code, I get this output:
What does this error code mean? Also, is...
Hi. We are using the nRF52 sdk v12.1 with S132 v3.0.0 on a nRF52832. Once in a while (could be after running a few hours, could be after running a week) the application ends...
Where can I find the right documentation to start understanding the Nordic Thingy FW? Do we have any design document for this?
I need to develop my own application on the...
Hello,
I'm looking for some general guidance on the following application:
1 nRF52840 based gateway to cloud, on power supply
a few hundred nRF52832 sensor nodes,...
We want to use app_timer_create/app_timer_start to create a periodic timer, but noticed that there were a few seconds missing. After printing out each tick, we see that there...
I can't open my tickets since it's changed into private ticket by your engineer.How can I do?
My ticket' name is"about service change can't receive BLE_GATTS_EVT_WRITE"...
Hi,
I will work with nRF51822. I installed all software tools and I connect target device with debugger.
Should I connect nRF51822 with power like battery (because I will...
I used SES and wrote a printf message at main entrance: when I run in nRF Connect I can see the message that I wrote just after I press the RESET button (OK). Still, as I...
Hi,
What is the GPIO pin state during reset, and during startup ? I have seen that it is a high impedance floating input. How much is the value of this impedance? Can I...
