after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I posted recently ( https://devzone.nordicsemi.com/f/nordic-q-a/40381/interfacing-with-mcp4725-with-twi-registers ) and after editing the post, I can no longer access it ...
Hello, boss, I used twi read/write data from others device, I find a strange problem, When in no-blocking mode, mainly loop use "sd_app_evt_wait" TWI can't write data to others...
Hi, all. I have been going through the mesh examples and have been able to do the light switching, dimming etc examples and have used the RTT as well as physical buttons to...
Hello everyone,
My problem is the next one :
I bought a Nema 17 stepper motor (this one : https://www.pololu.com/product/2267 ) and it’s driver (this one : https://www...
It appears to be an error in the function signature `sd_ble_gatts_hvx()`.
Since the call is made via software interrupt, the const qualifier is cast away regardless.
So...
I am trying to implement the HAL interface for USB devices in Mbed for the nRF52840. Mbed is currently on nRF SDK14.2 so I may not have all the most recent bug fixes for the...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
hi,
I am compiling nrf52840 light switch sample code in an embedded studio, I am getting the error as extern "C" {: Invalid argument, how to get out of this
