Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
I have a Thread network setup using nRF52840 as per the documentation below, using the Raspberry Pi image provided by Nordic. http://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
In my develop environment , there have many proprietary device. One device is working on PTX mode, and the other devices is working in PRX mode.
If the PTX device...
Hi,
In the FICR (INFO.VARIANT) register on the nRF52832 soldered on my board I can read: AAB0 and in the same register on the NORDIC DK I can read AAE0.
The only different...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
I have a trouble in my project.After flashing softdeivc,I flashed my application,but adversting is not work immediately, then a turn off the hardware and wait some second...
Hi:
I am developing my project based on ble_app_uart example. The development bench is SDK13.0, the chip is nRF52832.
One problem I have now is that: I configure Pin12...
When using FreeRTOS, external GPIOTE interrupts do not work.
And just how correctly to use the NFC with FreeRTOS?
In examples NFC use app_scheduler for events handling...
Hi
I've done a few attempts in the last years to implement a reliable reception by using the UARTE. In the past we used the UART periphery from the nRF51, but we thought...
Hi Everyone
I have the following issue in my application code.
If i configure a pin as an input pin , i am not able to run the ble init function in which it advertises...
Hi team ,
i am vishal working for VVDN Tech .
we are going to use 10k parts of nRF52840in our project.
so we need step file of that.
Awaiting your soonest response...
Hi,
I am trying ble_app_uart example of SDK 15.
When I do not connect Uart port (TX, RX) to other peripheral, I get fatal error (log via RTT).
```
0> <error> app...
Hello! I am now using nrf52832 sdk14.2 development, as a slave device, need to be bound to the phone, I now want to know the maximum number of allowed bindings and the current...
Hi support team,
I'm using nrf52840 and SDK 15.0. I need to add buttonless dfu service to my application so that my device could be able to upgrade firmware OTA.
However...
When flashing SoftDevice S130 v2.0.1 with nRFGo Studio ( JLinkARM.dll 5.12f ) and softdevice protection enabled, the UICR.CLENR0 is written with value 0x00B00100 (~11M Bytes...
