Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
This is the normal kconfig menu.
But it often happens that the following picture does not recognize anything in kconfig
and there is no devicetree option in the action...
Hello Nordic,
We developed our product using MCU NRF52840-QFAA-F-R. Our client is based in the EU. We plan to launch our product in 1-2 months.
I have a few questions...
Hello,
I am working on a prototype Bluetooth Low Energy module using the MDBT50Q-512K (by Raytac).
To measure the frequency of this prototype with test equipment, I am...
has been helping me connect to a device and I am finally able to do that, but as soon as I do, Zephyr crashes.
This is with a lightly modified central_uart project [00:00...
While creating a new board in step 2 of the exercise, there are a couple of problems with the sub-steps 1-5:
First, sub-step 1 says to name the board "DevAcademy nRF52833...
Hello,
I've been using the libuarte module in my project, and I done a power consumption reading. With libuarte switched on I'm consuming 0.78ma, and with it switched off...
We have been seeing a bootloop issue on some of our nRF52840 boards running NCS v2.6.1 using CR2032 coin cell batteries. The batteries are all around 3V.
This is an intermittent...
ON NCS SDK 2.7.0 version, how to calibrate SAADC?
I checked below code, I see that "Perform calibration before the reading is taken if requested.", it will trigger calibration...
I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
Hi!
I'm writing new firmware for the nrf54 family, and I want to have a system timer with 1s resolution (clock). This clock will be occasionally synchronized with epoch...
I am currently working through the Nordic Academy - SDK Intermediate Course - Lesson 2 Exercise 3, found here:
academy.nordicsemi.com/.../
I am not seeing any of the...
Hi,
Going through the nRF Connect SDK Intermediate course on Lesson 2 exercise 2 step 9 there is a command ncs_install_path/PathToToolChain/opt/zephyr-sdk/aarch64-zephyr...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I know the default answer is no, stopping nrf24 and get a RF52 or nRF53 series but my question is about an existing product. We are not all FORD, we can not just do a mass...
Dear Nordic Support Team,
I'm currently working with your Flutter library, mcumgr_flutter version 0.4.1, to implement Device Firmware Update (DFU) functionality. However...
