Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am writing to seek your assistance regarding an issue we encountered during the Matter certification testing. Our product failed to pass test case TC-S-2.2 , specifically...
HI
I am using the nRF54L15. Is it possible to integrate BLE Mesh functionality into the periodic_adv_conn example? This would allow the device to both receive data reported...
Could you please let us know in which NCS version Neuton ML is planned to be integrated, and whether there is a specific timeline? We are considering incorporating this technology...
Hello
nRF5340 and nRF54Lxx datasheet contains a section where the "AP ID"s of the "Debug access port" are described.
Is there anything similar for the nRF52xxx available...
We are working with Nordic's official Peripheral_esl and Central_esl samples from nrf-esl-bluetooth, using nRF Connect SDF v3.0.2 and Toolchain 3.0.2. Our setup is aimed at...
Hello,
I would like to ask and explain what the options are for uploading production firmware to Nordic chips, specifically nRF5340+nRF7002. So far, I have been using VS...
Hi,
I have a BLE Mesh network managed by an nRF52840 device (let's call it the central device). I can add and remove other nRF52840 nodes to and from the network (kind of...
Hi,
I’d like to implement firmware updates where a central device (SMP Client) updates a peripheral (SMP Server) over Bluetooth.
I came across this repository: github...
I’m currently exploring peripheral support on the nRF54L15 and nRF54LM20A series controllers. I need to turn an LED on and off using the PWM component. The LED is connected...
We are developing a device based on the nRF5340 with an nPM1300 PMIC. The device has three power modes :
Active mode: most peripherals are enabled, and BLE communication...
I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn...
Hello
I am looking to use [as much as possible of] the full-speed USB bandwidth of 12 Mbps (or 1.5 MBps).
I have been able to use the USB MSC for my initial testing (with...
Hi All,
VS Code version 1.105.0
Mac Silicon, latest OS version installed : Tahoe 26.0.1
Since yesterday, my "nRF connect for VS Code" extension is stalled : the...
Hello, I came across the Location Services page for nRF Cloud and noticed that it supports multiple location technologies, which is quite promising. One line that stood out...
I recently started tooling with Zephyr for low power Bluetooth applications and i was trying to build with sysbuild mcuboot togheter with my nRF52832 without success. I see...
