Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I'm using the Async UART API and the Enhanced ShockBurst API and my code seems unstable. The RF Connect Debugger frequently crashes.
The ShockBurst User Guide specifies...
Each time I attempt to use a Zephyr API on my NORDIC device, I face the mystery of what CONFIG setting are required to go with it. For example:
To make the Async UART API...
NCS 2.7.0 with Toolchain 2.7.0
I'm working on an out of tree application derived from the example application project.
I'm using sysbuild with MCUBOOT.
The processor...
Hello, we are using the NRF52810-QCAA in LDO configuration. On reference design, there is an NC decoupling capacitor on DEC2 pin.
Is it possible to completely remove it...
Hi,
Not sure if it's a zephyr issue or a LVGL issue, so I hope I'm at the right place.
I use an 1.54 eink display with the SSD1681 driver, and LVGL. Everything goes well...
Hi Nordic,
Board:nRF54L15 DK
Code Base:peripheral_uart
Issue: Added Zephyr NVS Flash support but encountered error -22 from nvs_mount(&fs). Additionally, data cannot...
Hi everyone,
I'm working on the nrf54l15 with the nrf sdk v9.0.0 wihch I assume integrate matter version 1.4. I'm using the google nest max as a thread border router....
I am developing on a custom nRF5340 board, but I encountered a BLE-related error. To troubleshoot, I built and flashed the basic example peripheral_uart , but the following...
Hi,
We are working with nrf53-DK evaluation board, and we are using P1.02\P1.03 pins for I2C communication.
We wanted to connect a 5V I2C slave on these lines can we connect...
Hello!
I am using an nRF Connect SDK V2.9.0 with a nrf54l15. I want to set up a project with a custom board. I want to add DFU in the future, so there must be MCUboot bootloader...
Hi everyone,
I'm currently working on a low-power application and aiming to minimize sleep current as much as possible.
Thanks to some great advice I've found on this...
Hey so I am making a capstone project with Drapers lab from University of Massachusetts Lowell and one of the requirements is to create an friendly end-user GUI instead of...
I want to confirm these questions,hope someone can give me some explaination.
1) RADIO has it's own kernal which is some kind of MCU.
I have looked through some doc on...
Hi I am using the nrf9160 with the npm1300 fuel gauge with ncs 2.7 For the function `nrf_fuel_gauge_process` there is a note for the vbus_present param ` vbus_present True...
