Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am considering a NRF52833 + nrf21540 combination. I see in nrf21540 product specification mentioned that
Single-ended 50 Ω matched input and output
...
Hello,
I want to create tfm_ipc project for NRF52840 DK board.
I configured options like below.
But I got an error message, "create_nordic_project.py failed (1)...
I looked at Blinky, but I am still not sure how to access the GPIO pins. In Blinky, there is an led0 alias, but what about other pins? What are there aliases?
Specifically...
Hello,
I used SDK15.3
Android phone and iOS phone is master
nRF52811 module is slave
It's said that the phone can't set conn international（Android、iOS）
But slave...
Hi,
i am working on "nrf52dk" . i want to use nfc pin as gpio.
what i did is
NRF_UICR->NFCPINS = 0<<0;
CONFIG_NFCT_PINS_AS_GPIOS included in preprocessor definations...
Dear Nordic,
I'm doing network registration test with nRF9160 DK in CMW500 test network environment.
I've set CMW500 configuration up as described at "https://devzone...
For a Non-RTOS application, take ble_app_blinky for example, the application is coded by us while SD is provided by Nordic.
My understanding is that the SD is running as...
Hello, All
I saw this description in the Bluetooth 5 Go Faster. Go Further document：
Advertising sets have an ID which is used to indicate which set a given packet belongs...
Setup:
Module: nRF51822.
SDK version:nRF5_SDK_11.0.0_89a8197.
Example: ble_app_uart.
Softdevice: S130.
I use ble_nus_string_send on the BLE_GAP_EVT_ADV_REPORT...
I'm following the NCS tutorials. I'm targeting the 52840 on the 9160DK board. I'm using SES with NCS1.6.
I'm able to get the hello world to run and the message is out on...
Hello,
we are developing a customer product based on the nRF9160 and Nordic's NCS v1.4.2 where we need to send battery test data every 30s (~ 1kB, PUT method). The communication...
Hi:
I am working on a stereo microphone application using the NRF52840. I would like to have the 2 microphones output 16K samples per second (8K samples each for left and...
