Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm new to using the thingy so I followed the instructional video to set up my 91. I think I tried to update the modem while not in MCUboot mode (I held SW3 when turning...
I have downloaded the latest version of nRF SDK (version 17). I am using Segger 4.50
The examples provided with the SDK use absolute paths, and will break if you relocate...
Hello,
I'm new here and I'm trying to program nRF52811 with direction finding AoA.
I notice that there is no code about it but there is steps to follow and that nRF52840...
Hello,
It appears that the LTE BLE Gateway example does not support the Thingy:91 out of the box. Is there a modified example for NCS v1.4.x (or later) that enables this...
Hello,
I installed nrfutil multiple times, rebooted my system (MacBook) but still when I type nrfutil on terminal it gives me the error "-bash: nrfutil: command not found...
Hi team
We are using your NRF52832 chip for product development based on the official nRF5_SDK_15.0.0_a53641a.
/**@brief Maximum amount of addresses in the whitelist...
I am trying to figure out the maximum transfer size for nrfx_uarte_tx . The documentation says to check the MAXCNT register description in the Product Specification. See page...
Dear,
We are planning to use Raytac Corporation’s BLE module MDBT42Q-512KV2 and which is deployed with Nordic nRF52810 solution. We hope that we can use
nRF SoftDevice...
Hi,
would nRF Connect SDK work smoothly with nRF52810, or is it better to use nRF5 SDK?
If nRF Connect SDK would fit, what would be the influence on electric energy consumption...
Hi nRF
I just bought the new PPK2 tool which I think is awesome. However I think there are some issues with it.
Issue 1:
First of all thy X axis scaling is wrong by...
I want to know how to use control model with interactive pyaci script. I can't see some of the elements with model while using compositiondata_get(). i.e, i can see all client...
Hi, my sdk version is 17.0.2, softdevice is s140, when i use the port pin P1.00 as the RX pin of the uart, it will show data bus error, i have tried use other pin as the RX...
Hello,
I'm writing a firmware for the nrf52840 with a GPS\GSM module connected via UART.
I would like to ask what would be the best library\approach to interact with this...
Hi,
I can't seem to find any example code for nRF51822 on Nordic website. I can only find that softdevice. I am trying to use nRF51822 for some BLE functions.
Thanks,...
Hi Nordic:
It seems that mesh LPN can receive secure beacon via friend node, and if has no friend, LPN also can receive secure beacon if MESH_FEATURE_LPN_ACT_AS_REGULAR_NODE_OUT_OF_FRIENDSHIP...
