Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I am trying to test ble_app_blinky_c.
I have problem with received data from peripheral which is my...
Hi,
I am new to the nrf52832 and I wanted to use its Bluetooth functionality for a project I am working on. I have read about the theory behind the Bluetooth stack etc,...
Hi,
Is there any sample Android mobile application available which calls or consume the Temperature/humidity for nrf5_SDK_for_Mesh_v3.2.0 ?
Best Regards,
Hi,.
I am using nRF52832 , sdk 16V
How many samples can be sent over ble if we set 7.5ms minimum
I need to send the 100 samples. I tested by setting to it 7.5ms I think...
H i everyone, I'm having a problem as follows: I am wanting to use LPCOMP to wake up the nrf52840 from system off mode. So can anyone give me an idea of how to do that?
I tried Searching for the NRF_CCM structure, but could not find it.
Where should it be nor the MAXPACKETSIZE.
this code is in the system_nrf52840.h
Also, could you please...
Hi
We are doing field trials of a nRF52840 product with s140 SD, now and again NFC stops working (tag type-4, read and write).
This has been seen in SDK15.3.0 with SD6...
Hello,
I would appreciate some guidance about BLE connection stability. Our product is a system of 3 peripherals (custom board with Laird's BL652 module, containing nRF52832...
Hi,
I have a project which requires using trace data pin P0.18 as an SDA for the sensor, but cannot send
anything because it doesn't generate anything and the program...
Hi, we are moving from nRF52840 DK to integrate nRF52840 to our solution. In the datasheet for pin assignments ( Link ) it states "recommendation usage; Standard drive, low...
I'm currently running nrfjprog version on OSX. Version info below:
When running a nrfjprog -e I expect that the device doesn't do anything afterwards. When monitoring...
I'd like to use two nRF9160s to do D2D (Device to Device). Is it possible? For example, if you press Button 1 on nRF9160 (1), then LED 1 on nRF9160 (2) is displayed. Is it...
Hi,
our company is developing some different models of devices with BLE based on the nRF52840 MCU, working with the nRF5 SDK (17.0.2). The devices are in parallel using...
Hi All,
I am working on the nRF52840 Zigbee protocol and I am using nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
With the help of engineers and other stuff, I am...
I updated the nRF Connect SDK to latest master. It currently uses Zephyr 7d20f2ebf2. Most of the time (~4 times out of 5), calling sys_rand32_get() crashes the firmware and...
