Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Maybe the question is abnormal, but is it possible to make the NRF24LE1 chip work on the Sub 1GHz band by setting the quartz to a lower (less than 16 MHz) frequency? Has anyone...
Greetings....
Since logging is removed from Mesh, I find it is very hard to debug the system. I wonder if it is possible to ask for your help to have a new monitor type...
SDK v15.2.0 using code from the peripheral spi example. Linux Ubuntu 19.04, uploading to nRF52 DK.
When I call my get_bma253_accel_data in main, I get a continuous stream...
The development of the custom hardware of an nRF52832 utilizing the u8g2 library has been shown to control a small display 64x48 SSD1306 driver. The prototype hardware another...
I have been migrating a project from SDK 14.2 to SDK 15.3 and have encountered an issue with UART. I am using the legacy layer with the following configurations:
I am...
Hello,
I'm evaluating nRF52811 as a long-range IC in a beaconing application.
Here's our specifications:
- The beacon must operate with Coded PHY
- The application...
Hi everyone, I know that the theoretical limit for the Bluetooth Low Energy throughput is 1 Mbit/sec, but I heard that on practice you get much lower. So I would like to find...
We were running BLE DFU bootloader for nrf52832 based on sdk 14.2; this worked fine.
We have now moved to sdk15.3 and nrf52840 as we needed USB.Our applicaton is up and...
Hello,
I have a custom nrf9160 device which requires
device stops at:
'Secure Boot: prepare to jump to Non-Secure image'
if I use this the following prj.conf:
...
Hello,
i I’m have a custom nrf9160 board. I have been using SES with j-link edu to upload firmware to my board with no issues.
Now I need to update modem firmware...
I'm trying to update my NRF52832 running s332 v5.0.0 and a stock SDK14.0 bootloader to S332 v6.1.1 with an SDK 15.3 bootloader.
I am including the flags --sd-req and --sd...
Hi All,
I am working on an NRF application that communicates with a specific mobile app, sends some measured data. Everything works fine except on some older (at least it...
Hi.
I wonder which pins are AIN0, AIN1, AIN5 AND AIN7 (on nRF52810 QFN32) ?
It seems the datasheet would tell...
I need this for a project at work.
Please. And Thank...
Hi,
I am trying to debug on nRF52840 dongle using JLink debugger and Keil uVision V5.18.0
What I have been through is here: https://devzone.nordicsemi.com/f/nordic-q-a...
Hello,
Greetings!!!
I am working on nRF52832 having SDK 15.3.0, Windows 7 and Segger Studio IDE.
Right now I am implement OTA in my custom application.
I upload bootloader...
