Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have implemented OTA DFU for Xamarin based on the implementation of Nordic's official library for Android . It works in general, but I'm seeing a bottleneck in...
Hi,
I would like to know how to process DTM test for nRF52840 BLE RF TX power, RX sensitivity ... etc.
If there is any test firmware, tools, command lines and application...
I'm trying to migrate to SDK15.0 (from 14.2) for the nRF52_DK and nRF25840_DK. Using the new nrfx_rng.c driver I'm getting a link error as a few functions can't be found:...
Hi,
I'm using nRF52840 with mesh 2.0.0 and started from the light switch example to build my own application. I have now 2 type of boards master (client+provisionner) and...
Dear Nordic Team,
Thanks for supporting.
currently i am working Single channel scanning with ble_app_uart_c example. In continuous scanning missing beacons. Please support...
Currently, in my application, any iPhone can attempt to read from one of my protected characteristics and initiate the bonding sequence. I have it set to "just works" mode...
Can anyone tell me if there is a specific problem on the nFR 51 using the 12.3 DK, where a disconnect is seen when it connects? I'm using Android Lolipop 5.0 on a BLU device...
Hi,
Im migrating from SDK8 to SDK12
app_timer crashes
Debugging at app_error.c shows m_error_data to be :
softdevice, pc 0x000104AE, fault ID 0x00000001 error_info...
Hello, trying to understand how to replace just the bootloader and s112 SD (app not installed), presently getting Insufficient resources.
First, mergehex -m softdevice.hex...
Hi,
Has anyone attempted to first transfer the entire image package to the external flash over BLE and then use a background DFU library to transfer from the external flash...
Hello,
I've got a NRF52840-DK development kit and tried to configure it with a ATT MTU size of 512 bytes (larger than 247 bytes). I've activated data length extension and...
HI all,
I'm trying to get the Thingy Mesh Demo v0.1 working on my Thingy's. I am using the same SDK version as used in the demo ( Nordic nRF5 SDK for Mesh v1.0.1) and I...
I was able to follow the "quick start" guide for Mesh DFU and got things working with 3 nodes.
1 node (the serial host hooked to the PC) was programmed with:
bin/softdevice...
Hi to all,
i am developing a device with nrf51822 soc. i am using nrf51822 custom board, my board is https://pl.aliexpress.com/item/2V-3-3V-NRF51822-Bluetooth-4-0-Wireless...
Hi, everyone.
I am currently doing research for our new project - IoT alarm system for smart home.
One of requirements is Wi-Fi / BLE combo chip / module . Multi-protocol...
