Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm upgrading a client project from SDK 14.2 to SDK 15, and running into some undefined symbols in ble_dfu_unbonded.c:
Error[Pe020]: identifier "nrf_dfu_set_adv_name_svci_async_t...
Hi,
I'm trying to use the pc_ble_driver_py framework and an NRF51/52 dongle to connect to a BLE device. The BLE device in question has some custom defined services for operation...
Hi all, I'm currently building a bootloader suitable for Dual Channel DFU and SD132. It is on nrf52832, currently on PCA10040, using SDK 14.0.0.
Although the linker script...
Hi all. I try to configure QSPI example to work with w25q64fv flash. I connected all pins from flash to same pins on nRF as on PCA10056 DK board. After all i have "Data inconsistent...
Looking at the code in SDK 15.0.0 I think app timer library will be reinitialized. Is there a way by which I can check it the library is already initialized and initialize...
Just installed Mac v. 2.4.0 of nRF Connect, and the "Start Scan" button is disabled. Here's the log:
2018-07-05T13:43:15.834Z INFO Application data folder: /Users/rob/Library...
Hello,
I am developing on the nRF51 and soft device version 8.0.0.
I have created a new service that has a 128-bit UUID that is based on the base UUID: 00000000-0000...
Nrf51822
SDK : nrf51_12.2.0
soft device : s130
Example : ble_app_beacon
I’d tried single channel adverting with nrf51 beacon. And I referenced this way to disable...
We are using the nrf51822 chip, however after typing the command: nrfjprog --memrd 0x10001080 -f NRF51, the chip is no longer able to start.
We have tried resetting the...
Hi Everyone,
I have successfully configured RTOS and BLE alog with onboard LEDs blinking into an RTOS code.
Everyhting runs fine if i run only the 4 tasks of LED blinking...
Hello!
I need to send 20 x 20 bytes with the nRF8001 and would like to reduce the transmitting time as much as possible to set the MCU and nRF8001 in sleep mode as long...
Hi,
I am confused about the ROM layout, would you please correct me? Thanks.
Based on my understanding, for open bootloader scenario(like nrf52840 dongle), the bootloader...
I am using the nRF52832 with the S132 soft device. I am trying to send a large amount of data (~5 kB) from a phone to my BLE peripheral. I am wondering if the queued write...
I Have attached my project which is an SDK 15. project, starting with the simple twi sensor project and including some functions calls from gpio from SDK 14.0, porting gpio...
Hi,
The following is the guide under this ticket: devzone.nordicsemi.com/.../where-i-can-find-the-example-of-usbd-dfu-for-pc-side
Terje said "you can use nrfjprog with...
