Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have this program running on KEIL 5, what could be the problem with the code and Do you guys have any sample code for mcp9808?
Note- I am using the wired connection not...
I'm using SDK11 and PCA10028.
hrs works well, but did not bond with central(both android(kitkat) phone and iphone) in the nRF Toolbox app, althogh it's device manager ported...
I was wondering if anyone has done any extremely high speed UART work on the nRF51 (or the non-EasyDMA module on the nRF52). I need to improve performance for an existing...
Hi,
I ran the ble central example code on nrf51822 16KB ram version without any problem. But when I run the same code in nrf51822 32KB version, the program flow goes to 0xFFFFFFFE...
Working on my first project in mbed using the Nordic nrf51-dk.
The project utilises a TMP112 temperature sensor and attaches the reading to the service data to make it...
I'm trying to rename my device using s130, but the name doesn't get applied.
I went back to the "roots", ie the HRS sample.
Just before entering the loop, I add a name...
Hello,
I am working on a custom board with NRF52832-QFAA-R7 and trying to run ble_app_uart_c on it. I am using uVision 5.23.0.0
The first trouble that I am facing...
I'm trying to implement usb function on the nrf52840. The moment that I connect the usb to the computer the chip resets.
With gdb debugger i found out where the fault happens...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
Hi all,
I like build a smartwatch-like device that can receive notifications from my android phone. The bluetooth device has a oled screen and displays what notification...
I need to turn on and off one pin around every 100 us. Time between must be 1 cycle (couple of ns) and can't be interrupted at any circumstances.
Without a softdevice I disable...
Hi All,
I am a beginner in nrf52.
I need to get the client device address in ble_app_hrs_central, because I have more than one devices connected.
There is a hrs_c_evt_handler...
