Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
Has anyone been able to succesfully use the HID Keyboard Demo (ble_sdk_app_hids_keyboard_main from Nordic nRF51822 SDK ver 6_1_0 along with GCC compiler for s110...
I have an application working using PPI to start a SPI master transaction from a GPIOTE event. Unfortunately, I currently have very high current consumption which I am led...
hi all,
i try to use to timer to have a single press and a long press.
this my code.
const nrf_drv_timer_t TIMER_BUTTON = NRF_DRV_TIMER_INSTANCE(0);
const nrf_drv_timer_t...
I don't know where it is used..
example, when I use sd_ble_gatts_hvx(conn_handle, &p_hvx_params), conn_handle was BLE_GATT_HANDLE_INVALID(0x0000) result of debugging. ...
I use nRF5_SDK_12.2.0_f012efa to develop BLE application in IAR workbench. Now I want to test the example: ble_app_template_pca10040_s132-nrf52832_xxaa. The project can pass...
First off, I have worked through Vidar's excellent tutorial located at " devzone.nordicsemi.com/.../" and have successfully built and run the blank blinky example so my installation...
Hello,
I am trying to change the MAC address of my device nRF52, by using NRF_FICR->DEVICEADDR[0], NRF_FICR->DEVICEADDR[1], I am able to see the device address.
But...
Hi I am using SDK 12.0.0.0 in nRF52832 in this code when I am using __enable_irq(); function for enable the interrupt then controller is getting reset can anyone help me regarding...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
Hello lovely Nordic Semiconductor staff (and everyone else reading this),
I have recently been working on exploring the use of BLE via Nordic chips in my employer's products...
