Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am reading battery voltage using nRF51822 microcontroller. I set the ADC configuration as 8 bit the result should be 255 but i am getting around 511 value. I am not...
Hi,
We tried to run the blinky example in the contiki source tree, and we had a strange behaviour. The example code is here , and the hardware is here .
The issue is...
Hi,
I'm using a RF module with nRF24L01+. Sometimes the RF stop working, the module keep replying status of no rx data (all pipes).
The device is embedded into a device...
Hello
I'm testing latest examples on 10040 (SDK12 S132). I want to get autoConnect working on Blinky example with nRF Connect app but I'm unable. Has anyone tried this...
HI all Nordic Developers,
Recently, I am using nRF51 DK as a beacon scanner connected to my laptop (Baudrate: 115200), it works fine to detect the beacon broadcast from...
HI,
I am using development board of BLE nRF52832 battery which you provide CR2032 is support for good battery backups
please give the reasons behind in it?
Hi all,
Is the "to-be-sniffed" advertisement packet allowed to have incorrect CRC, or perhaps a missing CRC? I.e. Is it possible for the sniffer to just display the raw...
Hello,
A problem occurs when i run the DFU over UART on my board.My bootloader project references to nRF51_SDK_9.0.0_2e23562\examples\dfu\bootloader\pca10028\dual_bank_serial_s110...
ANT experts,
I have been looking at the nrf52 implementation of the ANT timestamp (and timesync) features. One thing that is rather puzzling is the fact that the documentation...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
