after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am trying to implement SCCD on S130 v2 sdk11 but this is not in the scope of the tutorial.
I have populated the structure just the same as for CCCD, but I can't have the...
I need to read / write data over RTT with an nRF52 target device. There are function prototypes in nrf52_nrfjprogdll.h that look like what I need.
Before I spend the time...
Hi, I want to connect to a simple Bluetooth device with the help of NFC, no pairing shall be performed. In short, I just want to get the MAC address of the Bluetooth device...
Hi,
I have a situation where our central device needs to be paired atmost with 1 peripheral. I can put a central device into repairing mode for 3 minutes. Within this time...
Sorry for a non-tech question. I've worked in a project using a ble module from nRF51 serie, and in this project we've implemented the suggested Nordic DFU profile described...
hello there,
I use currently 'ble_app_hids_keyboard_s132_spi_pca10040' app of SDK11 for my nrf52832_xxaa device on 'IAR' IDE. It utilizes sofdevise s132. I do not use the...
On nRF Connect v1.0 production only
GENERAL RULE TO KEEP THIS PAGE READABLE
This is ONLY for already confirmed bugs which are discussed in another threads. Please...
Hi Nordic's community,
I have a question about how to write values to different characteristic in one time ( the values to write are inferior to 2O bytes) with an Android...
Hi
I've implemented a BLE peripheral based on the SDK11. For bonding i'm using the new peer manager. If the code runs on a nRF51 DK the bonding works properly. After the...
Hi
I'm having problems with the I2C. For now what I see is the twi_transfer function remains in infinite loop. Other symtomp is the SDA line remains normally at low level...
Hello,
I am currently trying to transmit around 800kbps of data using the Nordic ESB protocol. I am also attempting to sample 2 inputs using the SAADC at around 32 khz...
Hi,
We try to communicate between nRF51822 SoC and a GPS module through UART on a custom board but failed initializing UART.
More details:
We use nRF51822 as a...
Hi i use a soft with DFU and Beacon.
I will use the beacon and when i press on a button i can update the software with DFU.
DFU and BEACON works independently but when i...
Hi. We are going to mass production now and the 3rd party lab that will certify our product says we need to have a special mode in the firmware that would do :
continuous...
