Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I built a device using the nRF52832 SOC, have programmed it with the Version 16 SDK>ble_app_uart_pca10040_132 using Segger Embedded Studio. I am able to connect to the nRF52...
Hi,
We are developing a product using NRF52832 chipset with a small 128*160 LCD (based on st7735s controller using 8 bit parallel interface).
I noticed that there is st7735s...
Are there any limitations that will not allow me to make the ble_app_hids_keyboard example with FreeRTOS?
If no, is there any examples that will help me easier to migrate...
Hi,
I see that Eddystone packets has service data limited to 20 bytes frame data. But unfortunately I have to encode more than 20 bytes.
So can I use advertise mode as...
Hello everyone.
I have made the next solution for merging softdevice into debug fw.
i 've added the next lines in ld script
MEMORY { SD_FLASH (rx) : ORIGIN = 0x00000000...
Hi,
I want to output a high & low voltage with an array, the array contains a sequence number, looks like: {0, 1, 0, 0, 0, 1, 1, 1, 1, 0, ...} , and the length of the...
I'm wanting to create and Android application that can communicate with a nrf24l01 module. Is there an android library available that will permit this? Thanks in advance!
Hello Everyone,
Consider i have 2 MCU's on board connected via UART interface, one is any ( Target ) MCU (MSP32, STM32, etc) and the other is Nordic's nRF52832 ( Host )...
Hi,
We have two nRF9160DK and both have the SIM card issue as below, and our development was blocked by this issue, so please help check it, thanks!
original case
Hi!
I am trying to figure out the app_timer_library but am running into some (to me) strange behaviour. For the first seconds it appears as if the LFCLK is running much...
Hi,
I've built a application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently the...
Hello
I successfully build asset tracking example , for nrf9160_pca10090ns
when I try to run using segger, I get the following:
SPM: NS image at 0xc000
SPM:...
Hi,
I am trying to use the Android-BLE-Library with my nRF52832 device (I do have another test Android app which can work w/o using the library).
I followed the Github...
I am porting RF evaluation code to the nRF53 NCS/zephyr/Segger Embedded Studio toolchain, using only the network core to start.
How do you recommend configuring the network...
