Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all,
I am trying to deploy the long range mode in nRF58240 DK. I modified the Blinky example in SDK 16.0.0.
It just keeps reseting and the code error is 0x0007. Is...
Hi. We are using the USB CDC example to send data to a windows PC over virtual comport.
First question is that in the sdk_config.h file NRFX_UART_DEFAULT_CONFIG_BAUDRATE...
Hi Nordic Team,
Please suggest logic to scan all peripheral devices by the central device.
In my BLE project when I'm trying to scan all peripheral devices which are advertising...
Hi Nordic Team,
In a BLE project we need to configure same device to conditionally act as central (to scan) device and peripheral(to advertise) device based on the state...
If I write to the MWU REGIONENCLR register and immediately access memory that was previously watch enabled an event is still generated. If I delay a small amount (tested with...
Hello,
we have made our fist device with a custom Service with 5 characteristics. And now we have a strange problem which I was not able to debug to find a solution.
We...
Hello,
if I call this code all works:
if I call following code only ZB_ZCL_ON_OFF_SEND_ON_REQ take effect on target
I'm simply swap the call order, where's the error...
Good morning everyone,
I saw this question asked a few times, but no conversation was actually fixing the issue.
I am developing a product where I want the pairing to...
This seems to have changed in recent SDKs, so that none of the examples or techniques mentioned in previous posts is relevant any more.
I am using the SDK v16.0.0 ble_app_blinky_c_pca10040_s132...
When I carefully follow the instructions at https://infocenter.nordicsemi.com/topic/sdk_tz_v4.0.0/thread_ot_libraries_building.html , I am missing some of the openthread libraries...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
