Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I'm wondering if the current nRF sniffer firmware (v3.0.0) can detect extended advertisements on arbitrary channels? Is it supported in the firmware? If so, can I use...
Hi all,
I did not do mesh SDK for a long time. Now when I see SDK Mesh, I saw Low power Node example. It can run with Mesh network and update OTA by DFU buttonless (I don...
Hi,
I had an experience with embedded programming but never with wireless technology. I am using Nordic SDK v16.0.0 and nRF Mesh SDK v4.0.0.
Here is a short description...
Hello All,
I am working on the Nrf52810 board with sdk 14.2.
I have implemented the read ,write , delete feature in my code.
Now it is creating new entry for repeating...
Dear All, I am trying to compile an application based on the Zephyr project for the nrf52. I am following the instructions from here .
I am using Windows. Using SES everything...
Thanks in advance.
Hi guys am working with nrf5282 (softdevice s132 V1.6.0 and SDK version 15.2.0), also enabled freertos, and also make softdevice changes rleated freertos...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
As part of my Factory setup we want to download MBR, bootloader, SoftDevice...
Hi,
I would like to perform DFU over Mesh. I am following the steps
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v4.0.0/md_doc_libraries_dfu_dfu_quick_start...
Hi,
anyone help me.
I am facing the issue during DFU with OTA. the steps are listed which had I done,
here trying to update softdevice.
1. Erase all.
2.flashed softdevice...
hey guys,
I want to write a c code to display temperature sensor data which is inbuilt in the nrf52840. I am using segger embedded studio. Can I get some reference code...
SDK: 15.3.0
Softdevice: S140 6.1.1
Brief usage: multi protocol radio driver 1.5.0, uart1, spi1, twi1, saadc, ble, gpiote 2 inputs, pwm1
I have been finding high current...
Hi,
I'm running into issues with the watchdog never firing. I'm using SDK v15.3.0, with S132 v6.1.1, and a custom bootloader (based off secure_bootloader example).
The...
I can successfully download an image using nrfutil dfu serial when I use a test image compiling the bootloader with the Nordic default public key.
I cannot successfully...
