Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Help ！
I use ANCS need change ATT MTU to more , but I met an incredible thing .
just change NRF_SDH_BLE_GAP_DATA_LENGTH to 189 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 185
...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
As i an trying to establish LTE connection using nRF9160.but i want to use external antenna because i will place nrf9160 module in metal enclosure. please suggest best antenna...
Hi pals!
I'm trying to do the throughput example with using 2 nrf52840DK. I downloaded SDK15.0.0 and I'm using ble_app_mtu_throughput example under ble_central_and_peripheral...
Hello there,
I've been following a guide Installing a 6LoWPAN enabled Linux kernel and required modules as a part of setting up a BLE 6LoWPAN border router on Raspberry...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
Hello everyone
I am using nRF52840+wifi module to communication with the server via MQTT+LTS, Now MQTT communication with server was successful, Considering the safety,...
Hi everybody!
We have a problem with our product. It is based on nrf52832.
We used heart rate example in the SDK. MCU sleeps after a while if it is not connected. We have...
I'm trying to combine conventional pairing with OOB NFC pairing, but I'm struggling to decide which libraries to use. I have been looking at the examples, and they all use...
how can we properly set the scan timeouts? Say if we need to scan for a device for 5 seconds and if it is not available we can stop the scan and search for a new device. i...
Hello I am getting fatal error and system reset after calling APP_UART_FIFO_INIT.
I want to receive some data over ble and send it to the uart. I connected physical UART...
Hello, in my application I have a problem with the app_timer module respectively with a timer I have created. I'm working on a nrf52832 ( Rev. 1 - build code QFAA-B00) and...
I need a solution for doing a DFU from an Android phone to a device with a nRF52832 chip in it
I currently have a working version in IOS Swift but cannot get the Android...
