Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello.
nrf52-quadcopter question.
nrf52-quadcopter source code download is ok in github
website bluetooth connection is ok.
joystick operation need to excharUUID(0x0004...
Hello,
I am developing Bluetooth 5.0 application which advertises two different beacon advertising data sets (Each set with different advertising interval)
I am using...
I'm using SDK 12.2.0, SofDevice 3.0 and my chip nRF52832.
In my boot-loader project i disable IS_SRVC_CHANGED_CHARACT_PRESENT by define to 0.
The dfu process is completed...
Hi
with SDK15 SD140 6.1.0. I'm trying to use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED with CODED physical.
I run the following code
and getting...
Hello Community,
The PCB project I'm working on is ready to be optimized for production. What I am concerned with today is the electromagnetic compliance of the PCB.
In...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
In my project I have to implement passkey or whitelist in the conection with...
Hi,
I'm trying to run the OTA DFU for the nrf52832 (sdk v14.2, softdevice v5.1) from multiple devices.
In the OTA script, I enabl the receipt notifications and it works...
I am working out of this MPU-twi example and am trying to validate sent data by printing it to the serial monitor. From what I've seen in SDK 15.1.0 examples, it seems like...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
