after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
Using SDK 15.0
Example project: examples/dfu/secure_bootloader/pca0040_ble/ses
Segger Embedded studio V3.50
File main.c line 52
#include "uECC.h" <------ "No such...
chip：52832
sdk：12.3 ble_app_template
when I measure the sleep current consumption use the nordic PPK
I found there is a 30ua peak in every 20ms，could you please tell...
I have some questions to Bluetooth mesh.
1. If I have a mesh Network is it possible to have a connection to a device over all the nodes? Or does mesh just support brodcast...
Hello!
I am a beginner.
I am trying to communicate with the SD card with SPI using nrf 52832.(BLE Nano v2)
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
Hi, Could you send me a sample to send "Hello World!" string from sender task to receiver task?
I am using C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral...
Hi, I have a question regarding the behaviour of a button in the nRF App in Android, sometimes the button "READ STATE" in the "Generic On Off Server" configuration changes...
