Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
Hi,
I'm trying to use the nrf52832 with a sdcard application in SDK_13. I based my code on the example provided and managed to get the sd card working without any problems...
The error "Unknown command add_pc_lint" appears when running the bootstrap command during setup. It looks like PC-Lint is an application for windows for software debugging...
Hello! I'm trying to find a list of boards that can be integrated into a circuit design which have already received compliance in the EU, UK and with the FCC. I found this...
Hello. i testing zigbee coordinaator example with zigbeee device. Device was joined to Zigbee coord/ network.
Couldn't i get device payload data in coordinator source code...
I have the UART configured using the standard boiler plate code, with flow control enabled, where the RTS output is assigned pin 5.
I have defined a GPIOTE pin 25 as an...
We are working on a solution that involves a central provisioner that provisions a MESH network of sensors that it subscribes to. We need to be able to replace this central...
Hi,
I am currently drawing up a schemtic involving the NRF52832 on Proteus 8.
I have been trying to find symbol, footprint, and 3D models of the NRF52832 online, however...
Hi!
We are using a custom bootloader for our device. Current version of this erases everything from 0x0 to bootloader start address, and then writes MBR + Softdevice ...
Hi,
I have a question about ADC reading in ble_app_uart__saadc_timer_driven__scan_mode in SDK 14.
Let's say I'm using a double buffer, and I have 3 ADC channels (so...
Hi,
In my project, I am use nRF52832 for controlling ws2812b led strip with 8 leds.
I am use SDK 14.2 and s132_softdevice_5.0.0.
I have problems with the latency of...
I have a custom board of nRF52832-QFAB-B0 on which my application works well with SDK15.0.0 & SD132 v6.0.0
To perform DFU,
1. I copied the relevant parts of ble_app_buttonless_dfu...
