Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have been having issues with two different DK:s. I am doing bootloader development and suddenly the kits go unresponsive.
nrfjprog returns the following error...
Hi everyone. For our product, we need to accomplish tests for CE certification, in accordance with regulations EN300328 paragraph 5.4.10. How can we set the softdevice s310...
I try to integrate the ble peripheral uart example and the beaconing mesh example. It build completed. But when i build and debug on nrf52 board. I have some errors about...
Hello, im a beginner in circuit design, and currently i am developing ESB device that should work on batteries.
Device simply represents a nRF24L01+ module, an ATmega48...
Hi,
I am using nordic nrf52832 nRF5_SDK_14.2.0, I use the RTT for debug, I want MCU in low power mode,so I add the following code:
while(1)
{
NRF_POWER->SYSTEMOFF...
There are parallel 8 bits input to nrf52832 GPIO pins,I want to read the data from the pins and writ it to a RAM.how to do read the data in one CPU clock?
As per this document ....
nrf5_SDK_for_Mesh_v1.0.1_src/doc/introduction/mesh_hw_resources.md
The mesh stack uses flash to store the following states:
- Encryption keys...
We modified the ble_app_beacon example to advertise the beacon once a second.
#define NON_CONNECTABLE_ADV_INTERVAL MSEC_TO_UNITS(1000, UNIT_0_625_MS)
As a result of...
Hello all.
Sorry for the nube question, but I am really struggling to try and get my IMU data from my MPU9250, to send constant notifications through BLE using the NRF8001...
When using BLE_GATTS_VLOC_USER I would tend to make the variable pointed to by ble_gatts_attr_t.p_value volatile to reflect the situation that the value can be changed by...
Hello,
I am new to nrf5 mesh. I have setup my system based on Nordic's documentation and was evaluating Serial Example with Interactive Py script.
My setup consists of...
Hi:
I have a project which nrf51822 exchange some data with TI cc2541.There is a serious issue that the nrf51822 is occasionally reset by the watchdog when it communiates...
Hello all
I am trying to get out some debug messages from my custom Firmware (and board) but the log looks like this:
<info> µ“°8$Mø@ñ¨ó¹)F¨: NRF_LOG initialized
...
Hi,
can you please to provide a more information regard power up sequence?
for example:
we would like to use DC2DC (instead LDO) with CR2032 battery.
the PCB have...
