Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi I am using SDK 12.0.0.0 in nRF52832 in this code when I am using __enable_irq(); function for enable the interrupt then controller is getting reset can anyone help me regarding...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
Hello lovely Nordic Semiconductor staff (and everyone else reading this),
I have recently been working on exploring the use of BLE via Nordic chips in my employer's products...
Hi,
How to store two application image in nrf51822 flash each image size is 60kb. I have enough space
To store images but I don't know how to store. Please guide me to...
How can i reaed 32bits word using spi ?
I don't find the function to configure the SPI to read 32bit word ?
And how top start reading ? Is this function"uint8_t nrf_spi_rxd_get...
I am seriously stuck on a project. Expert help is needed.
The goal is to create a modified dfu ble bootloader with the following properties:
Target: NRF51DK (nrf51822...
I want to add nRF24L01 for nRF52832,but nRF24L01 needs to use software to ctrl TX and RX,I hope it auto.
nRF51822 can connect to PIN30(VDD_PA) ,and nRF52832 I need to connect...
I'd like to sample the SAADC at 1280Hz. The app_timer minimum seems to be 1ms (1000Hz).
If I use continuous sampling by setting SAMPLERATE then the minimum rate seems to...
Hi all,
I am trying to port the nfc_text_record to the example experimentral_central_ble_app_blinky after I am able to compile I am getting the following message on my...
Hi
Whitelist function is in ANCS sample code.
Does it require in ANCS?
Can I disable whitelist?
If yes, how many pairing times between Device & Apple OS?
It cannot connect...
