Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
I`m using MDBT50QRX (Raytac Nordic 3rd party for modules) I need to connect and program the firmware hex file (connectivity_4.1.1_usb_with_s140_6.1.1.hex) which is on...
Hi,
Intention:
I want to build and run a sample application without suggested IDE on my custom nRF52811 PCB.
Previous steps:
Based on a tutorial [1] I found I was...
Hi,
I successfully tested ecdh and aes256 in seperate projects but I want to combine them.
This is my code:
Problem is that when i call the ecc functions this happens...
Hi, I'm using nRF Mesh App to provision more than 5 devices for vendor specific models other than on/off model. My purpose is to send some data instead of on/off the light...
Hi all
I am using a nRF52840 with SDK 15.3.0 and s140_nrf52_6.1.1 soft device.
My application is a multi-peripheral device that has a common service, each peripheral can...
Hi
I'm really new to this, forgive me it's a stupid question. I'm using the nRF52 DK from Nordic.
I started with the "Developing with SEGGER Embedded Studio", but when...
In the user manual of nrf52832 it is said that ram[n].power are retained registers in sleep mode and that depending on the settings.
One or more RAM sections can be retained...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
