Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am designing a PCB with NRf52832 IC. I have a query regarding the width of the feed line. In reference design files, the width of the feed line is 30mil. I have...
Hello,
I want to receive the More data ( >20 bytes ) in nrf51822 Board from the nRF ToolBox UART module.
is this possible?
What will be changed to be done in peripheral...
Hi,
I have designed a custom PCB using NRF52832 IC.I have followed Sparkfun NRF52832 breakout board for placement of NRF52832 IC core part(including antenna) which is similar...
Hi,
I am using nRF52832 with NUS and buttonless DFU running well next to each other (SDK13). Instead of the standard way to jump to the bootloader (writing a 0x01 to the...
We have a device running SDK 11, without a crystal. It was using:
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16,
.rc_temp_ctiv = 2}
...
Background:
In a previous posting I had asked if anyone knew of BLE connection parameter guidelines for Windows 10.
The general response was, yeah ios has BLE connection...
Hi all,
I have a use case where I have about 40 buttons that can be pressed anytime. I need know when these buttons are pressed on multiple receivers devices. So every...
Hi ,
I would like to know about Bluetooth 5 compatibility with smart phones having Bluetooth 4.x
The observation is-
a)the android application scanning for BLE device...
Hi,
I'm trying to setup 3 server and 1 client.
Currently, I encountered a problem that a successful provisioning to 3 servers happened only when the power of client is...
I tried importing the Keil 5 SDK 13 project from github.com/.../nRF5-ble-timesync-demo into Segger.
I followed all the directions from devzone.nordicsemi.com/.../ However...
Hi,I have trouble when I try my nRF51822 board with example program of hrs. I use nRF Master Control in my phone to connect with my board.scanning is ok.But when it try to...
Hi guys,
I'm investigating on a problem we found in our system. It seems not related to our custom pcb or firmware, you can replicate it with the following setup.
Setup...
I will need to store some data (and edit it again later) and fetch it later in the nrf51dk even after turning it off and back on.
How can I store such persistent data in...
