I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I have a custom nRF9160 application running based on asset_tracker_v2. It is working perfectly but I am seeing location error messages. The nRF9160 we have does not have GPS...
Hi everyone! I have a custom board with the Adarfuit UF2 Bootloader ( https://github.com/adafruit/Adafruit_nRF52_Bootloader) and a SoftDevice. With the old SDK v2.5.1 I created...
Hi! So I am trying to control two micro servos, MS18 with the nRF connect app. So far I have the code where I can control it with one instance, and hitting the true false...
I am trying to work with a BLE Mesh network. I am using the nRF5340 as a light and another board, the BGM220, as a switch. Both are provisioned and configured, but the switch...
Hi everyone,
I'm currently trying to build a program with the extension "nRF Connect", and here is how i proceed :
- add build configuration --> nrf5340_audio_dk/nrf5340...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
Hello,
this is the first time I work with this device and the device is not for me or for my company.
I have to do an automatic test application, which should program...
Hi there,
So I am using an adapted version of the echo sample for I2S in the nRF Connect SDK in VS Code. I only want to use the echo example in receiving mode, so I have...
Hi, I'm using the nrf9160 with ncs2.7 on a custom board. Does the APN need to be explicilty set with `CONFIG_MODEM_ CELLULAR_APN` ? Or will it auto detect? Does it depend...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
