I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi there,
I am developing a BLE dongle on nrf51822. There is no external 32.768KHz crystal oscillator on my customized board(only has an external 16MHz oscillator)....
Hi, I’m trying to enable signing with MCUboot in my NCS v3.1.0 project, but I can’t get the app to start once I turn on signing. The build succeeds, I flash build/merged.hex...
Hi all,
I'm trying to perform aws fota on my nrf9151, I've followed this https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/networking/aws_fota.html#aws...
We are using the nRF9160 with a cellular service provider that has quite a strict firewall policy. There are rejected connections and we suspect a problem with cached DNS...
Hi,
We are in the process of changing the 32.768 kHz RTC crystal in an existing product and require additional data to verify the electrical properties of the crystal. ...
Hi Team,
We are starting new product development using nrF9160 modem.
I saw that new SDK available is v3.0.2. I hope we have to build/compile it in VS code, am I correct...
Hello!
I would like to use OTP storage on the nRF54L15, as explained here: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/security/key_storage.html
That page says...
[MatterTest] 09-25 08:50:35.568 INFO ***** Test Step 2.3 : TH extracts the Authority Key Identifier from the PAI certificate [MatterTest] 09-25 08:50:35.568 INFO ***** Test...
I modified the blinky sample to toggle io pin 1.05 While the app does compile and the originally led does flaash, I'm unable to control any other io pins. Using NRF5340 NRF...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for BLE scanning and advertising. scanning and advertising is working parallel. this is controlled by other MCU over serial...
Dear Support Team,
I’m currently experiencing an issue with Segger Embedded Studio where no output is shown in the Debug Terminal. It was working perfectly before, but after...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
I have a Central using nRF52832. The project is working correctly but I’m having trouble getting FOTA via BLE to function on top of it.
I’m using NCS 3.0.2 (3.1.0 and...
Hello everyone,
I am writing an application with three sensors on the same SPI1 interface on my nRF52840. See the following devicetree section:
For all sensors, I use...
