I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
We have a custom PCB with external crystal for HFCLK. Can you tell whether the external crystal is used by default for HFCLK or it has to be selected in the HFCLKSTAT...
I am using timer 3 as a counter for my capacitor discharge time. Currently, the value of is always problematic because it shows with too many deviation values sometimes...
Hello,
Is there any user manual to the nRF Connect for Android? I guess it is quite simple tool, but I am complete beginner in the BLE and would appreciate some description...
Hello All,
Currently we have a nRF52832 firmware .hex file for mass production.
And we use "nrf connect - programmer" to firmware programming without any problem.
...
Hi!
I'm updating to SDK v1.7.1 and I am looking at the changes in LwM2M Carrier Library v0.20.1. I was previously using LwM2M Carrier LIbrary v0.10.2
The big change is...
Hello,
I'm trying to install circuitpython onto an nrf52833 dk board, and am running into a fair amount of trouble.
Wondering if anyone can provide a guide on the explicit...
Hello,
I am trying to port the 51822 project to 52833. I am testing the port to 52832 temporarily.
The 51822 project is a commercial product.
SDK – 17.1.0 SD-S132, PCA10040...
Hi ,
I check the datatsheet "nRF21540_PS_v1.0.pdf" but I confuse on page 22 "TX_Gain initialized with POUTA_PROD (20 dBm +/- 0.5 dB)".
Which one is correct??
1: Tx gain...
I’m trying to use the Power Profiler app v3.2.0 under nRFConnect for Desktop v3.9.1 with a PPK 1 attached to an nRF52 DK board (containing the 52832 processor), but am having...
Hello, i'm having trouble with my new Board Nrf5340, i cannot detect the board to my PC.
I connected with micro USB and when i'm going to the device manager, i'm not seeing...
Problem:
Tried to compile (west build --board nr52dk_nr52832) the C:\nRF\v1.7.1\nrf\samples\peripheral\lpuart project but it failed to compile. I discovered this after updating...
Hello All,
I am new to use Segger Embedded Studio and NINA-B406 module. I have installed Segger Embedded Studio V5.50d and EVK of NINA-B406 module having nrf52833 SoC. ...
Hello All,
I have taken usbd_ble_uart_freertos example and modified it for USB MIDI example (taken from Github) for nRF5 SDK and modified it to use nRF52833 SoC.
I am...
