I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
I'm thinking of replacing the software that was running on "nRF52810 QFN48, S112" with "nRF52810 WLCSP, S112". In WLCSP, the pin assignments of XL1, XL2, nRESET, SWDCLK, SWDIO...
I recently downloaded Keil uVision5 and am trying to run some of the examples that are found in nRF5_SDK_12.3.0 available from on Nordics website on my Nordic51 development...
Hello,
I want to control 2 PWM with different frequencies and hence I am using two separate instances. I want to use only the hardware and not the PWM library. Initializing...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_cts_c but when i run the code first central disconnected but when i going to pair...
Hi, I'm in search of any document listing in a simple readable way the main differences between nRF5340-PDK (preview) and nRF5340-DK. More specifically, I wish to be reassured...
Hi there,
for the first step we simply want to send characters from ATMEGA 16 to a Raspberry Pi / and receive them from Raspberry pi
with teh NRF52480 (itsyBitsy - Adafruit...
Hi guys:
I encoutered a issue:
A: I flashed a APP from SDK(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart.)
B: I found...
Hello,
I am using nRF52833, nRF Connect SDK v1.5.0.
I followed this link Zigbee: Light switch — nRF Connect SDK 1.5.0 documentation (nordicsemi.com) and successfully tested...
Hi!
I am trying use aws iot sample and over this the gps example to obtain location and transmit a aws iot core, but I have problem with manage of lte and gps functions...
My project uses nRF52840-DK to connect, bond and discover a custom service with two characteristics (TX and RX) and RX Characteristic has a CCCD (0x2902).
The flow of the...
I am using nRF5340 DK board to implement zigbee network.
I have just build connect SDK's zigbee example (network Coordinator) and seen utilization of RAM shown below.
...
Hello everyone.
I am trying to set the attributes' value of a custom cluster I have defined.
I have defined 2 attributes:
I have followed the same procedure...
Hi,
We are designing the Nordic 52840 into a product and had some questions about the power configuration:
For both REG0 and REG1, are there any downsides to selecting...
