Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi! I'm trying to understand the possibility of doing a FW update to an empty NRF52810 chip via a host MCU running Linux. We have this setup on a custom PCB, whereas the host...
Hello,
I have two quick questions about the nRF24L01+ chip that I wasn't able to find from reading its datasheet.
1. Is the chip pre-programmed by Nordic or does it need...
Hi,
What does the AT%XOPERID command do exactly? Does it just return the operator, or does it change settings too, such as bands, system mode, psm, edrx etc?
Kind regards...
nRF SDK: 16.0, Device: nRF52840, module: BTX480XE, softdevice: ANT_s340_nrf52840_6.1.1.hex
The setup:
BLE and ANT running on same device concurrently. The device is modified...
Hi,
I am new to OTA, wanted to explore OTA. Is there any available example code for OTA in the sdk 17.0 or mesh sdk and how to verify it. How to proceed with this?
Thanks...
Dear Community,
I have been testing eDRX on nRF9160. For that, I have modified nRF Connect SDK "udp" sample. I have set eDRX cycle to 20.48s. My program does the following...
Dear all,
I am trying to run the MSC example in order to learn how to develop an application with MSC capabilities in the future. I have already run the example in its default...
Hi,
I want to explore NFC for nrf52832, how shall i proceed so that i can able to read and write using nfc. I want to write from an external device to NFC and so that...
Direction finding is a new feature in BLE eco system. We can think of many applications for this technology. One well known is asset tracker. We can locate the coordiantes...
Our new prototype uses an ISP1807 (nrf52840 module). The schematic is almost the same as a previous working prototype based on the Ublox Nina B302. (also nrf52840)
I've...
Thanks in advanced. The platform is nrf52832 and sdk17.0.2. I want to use phone to update static key of peripheral ble device, is there an example for this?
This problem is very strange.
First,I install the software(nrfgo studio,nrfgo studio-win64-1212installer.msi) on the company computer,the colour of nRF5x Programming is...
Our peripheral application sends an L2CAP Connection Parameters Update Request to change the connection interval 30 seconds after connecting. For most hosts, it works fine...
