Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
My product is based on nRF52840.
I have downloaded nRF5_SDK_17.0.2_d674dde.
Example: ble_central_and_peripheral / ble_app_interactive.
pca10056 doesn't have iar project...
Now let nrf9160 register the network to the analog base station, set the network mode of the device to cat-m, and currently use the analog base station to send SMS, the device...
Hello everyone,
I'm working on a mesh application based on the light switch example. For this purpose, I'm using one nRF52DK (PCA10400) as the server, another one as the...
nRF Connect SDK - Install tool chain - Verify All - I encounter few errors . I have attached the log file. Kindly guide me how to correct those errors. MY OS is Ubuntu 20...
Hello, I just brought this board and I was playing with it but I'm unable to get it working, I'm using platformIO IDE and I have configured it to use Arduino framework but...
I've been having a ton of issues getting any of the application code to run on my Thingy91. Just tried updating the Modem FW to 1.2.2, however I'm not able to place my Thingy91...
Hi:
52840 with softdevice, I use External low frequency oscillator (32.768K) ,the system run normal,but some days later,system can't run. So,I find the problem，the problem...
The Bluetooth Core Spec version 5.2 says that the " maximum number of CISes in a CIG shall be 31."
Can the nRF52840 support 31 concurrent CISes in one CIG? If not what is...
I want to load the GPS routine project of 9160, but it fails. The error prompt is as follows:
one step
When I click OK, the following prompt appears
two...
Hi,
I have nRF52833 and nRF9160 on my custom board. Due to limited space available, trying to use a common SWD interface between the two SoCs. As follows: 1) SWDIO and SWDCK...
I add the MAC of acquisition device in the broadcast initialization of nrf52810 serial port routine, it can display complete. But I added the Mac to the template broadcast...
Hi ,
My firmware is almost done, and now is the time to optimise power cunsomption.
First, my software has a special mode. Each day it wakes up, communicate with a sensor...
Hello,
We are developing products with nRF52810 MCU. There are only 100 bytes ROM left now. We hope to update bootloader via Buttonless DFU in single bank way. Is it available...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
