Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi
We have a legacy product with around 100.000 active devices. We still need to distribute new firmware releases, and we are using the "Chained DFU" app for this purpose...
Currently, my environment uses a mobile network shared through a wired connection to an RT-AX57 router. I am working in the VSCode environment using SDK v2.6.1. Devices: Nest...
I am trying to connect a nrf5340dk to a Jetson. For now I am testing with an Arduino. I am trying to run the CanCounter example with a device tree overlay file. Also I would...
Hi,
I tried to implement the CAF LEDs module as described here . But when added the Kconfig variable CONFIG_LED_PWM =y I got the error message "CONFIG_LED_PWM was assigned...
Hi,
I was developing on Visual Studio Code earlier, and for some reason, I cannot build pristine. If I try to edit the build configuration, it never loads, and if I try...
Hi,
we are trying to make the NORA-B126 (specifically its onboard LNA) work with nrf sdk 2.3.0 by modifying the 5340dk dts and defconfig files as specified in the NORA-B1_SIM_UBX...
Hi there,
I'm working on NCS2.7.0 and nrf52840.
I used the chip-cert to generate custom DAC, PAI, and PAA with VID = 0x1234 and PID = 0x5678, then placed the...
Hi there,
Thanks for helping. We are using the nRF52840 DK along with the Power Profiler Kit 2 (PPK2) for power measurement. We are encountering periodic power spikes during...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
System: Windows 10, Vscode + Nrfconnect
I saw a previous post on same topic which fixes the issue by changing the settings in extension like said here ( changing extension...
We have pre-production product (based similar to the NRF9160dk setup with a NRF9160 (LTE-M, GPS) and a bridged NRF52840 (BLE). We are working through certifications for CSA...
