Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I am trying to capture steps and wrist wakeup ( https://github.com/zephyrproject-rtos/zephyr/blob/4c6b1e5a65e752c881183ddb4687fa0231b11cc3/drivers/sensor/bosch/bmi270/bmi270...
I have an nrf52840dk and tried it with a ble central example and it worked fine. Then now I want to deploy him to the nrf52840 dongle and he appears to not work and I also...
I was trying to build the ble_app_scan functionality in a well served project in my custom nRF52810 board. During project build I am facing these build errors in SDK v17.1...
Not sure where to report this bug but I noticed that when typing sample names in "Create New Application From Sample", some Nordic samples do not show up...
For example...
Hello Sir,
I am working on direction finding. I use the nRF52840 DK to flash the code onto an nRF52811 (custom board) that supports direction finding. In the build configuration...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
My project has a nrf5340+external flash, and an external USB-C connector. The device exposes a USB file system (FAT) which is hosted on the external flash partition, and appears...
Hi Nordic
Q1.
HW: nrf9160 customer board. One USB-to-RS232 cable is used for PC sending AT commands (UART2).
Another USB-to-RS232 cable is used for PC collecting modem...
I am currently evaluating the Nrf54l15 viability for a migration from the Nrf52 for our products. I've been able to advertise, scan and connect with success but I can't find...
Hi,
I'm trying to build the nrf5340_audio/broadcast_source application. I'm getting the following error: nrf5340_audio/src/audio/le_audio_rx.c:20:22: error: 'CONFIG_BT_ISO_RX_MTU...
Hi, I have recently created a board definition for our nRF5340-based hardware using the "Create a new board" feature from the nRF Connect for VS Code plugin. I'm using SDK...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
I am going to do dfu not by YOUR example(FOTA or UART……)
I flash_write() data to image-1 address，and...
Hello,
Very new to Zigbee. Trying to use nrf 5340 dk as a Zigbee Coordinator to connect to a Thirdreality and a Sonoff PIR motion sensor. No modification (expect adding...
I am using the solution for this exercise to have MCUBoot use the nrf5340dk's external flash for the secondary partition in my own project. I have done the following:
1...
