Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I'm trying to connect an NRF52840-DK to a MAX30101 Wing board via I2C/TWI. I've set up the TWI Manager to send a message asking the MAX board for its part ID.
This...
nRF5340 with NCS 1.4.0.
I'm using the NUS (code derived from central_uart & peripheral_uart sample) and i'm trying to send longer frame.
I have tried to add the following...
Hello,
I was trying to recreate the blinky program for the nrf52840dk using the nRF5sdk using Segger embedded studio.
I tried doing it by opening the blinky example code...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE using application. How to do that? I tried to assign the variable to the min...
Hi everyone,
Regarding the CDC ACM example I have a question. In the example, every time a button is pressed there is a writing. I would like the writing to happen every...
We are trying to use more than one nRF52840 dongles simultanuously on the same PC and within the same process using the pc-ble-driver library (pc-ble-driver library version...
Hi. I want to save sensor offset data to flash memory on chip.
I erased page 126 first, but no events were called.
I can only get 0 from the value of sd_evt_get function...
Hello Nordic Comunity,
I am new to the Nordic nRF52840 DK usage. I am working on the development of a connectable beacon for a longer duration.
Any type of help will...
Renode ( https://renode.io/ and https://github.com/renode/renode ) is an open source simulator and used by Zephyr OS for example to validate binaries for different architectures...
Hello Nordic Taam:
I follow the WEB steps below
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4.1.0%2Fthread_ot_performance_measurement.html
Software...
I'm designing a EEPROM type of memory using a SDCard. The write and read functions works fine, but the initialization does not work sometimes and it stays in a loop (because...
The size of flash of softdevice in the "s132_nrf51822_5.0.0_release-notes" is 0x23000 but atrually the size of the flash used by softdevice is 0x224A7, which I found when...
We are using nrf9160 as an LTE-M modem with the serial_lte_modem app running on it. Another chip (ESP32) communicates with it using AT commands and after a few minutes of...
Hi team,
I am working with nRF9160DK on NCS v1.3.2.
I am building the asset_tracker application and from my understanding when running running west build -b nrf9160dk_nrf9160ns...
