Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
I am using nRF Connect SDK (NCS) v2.9.0 for a Matter project.
Currently, the Manual Pairing Code generated is 21 digits long. I need to change this output to be 11 digits...
We follow the youtube video: www.youtube.com/watch
to add battery charging and fuel gauging to our nRF52832 Series project.
It works, but after we enable
CONFIG_PM_DEVICE...
Hi nordic team
I am working with the Nordic nRF5340 SoC using Zephyr RTOS .
Hardware
External QSPI flash:
MX25R6435F
QSPI configuration (DeviceTree):
...
Hardware: nRF9151 DK Modem firmware: mfw_nrf91x1_2.0.4 Carrier: Verizon (PLMN 311480), Band 13 Antenna: External Problem The modem continuously reselects between two cells...
Hi Nordic team,
In the context of adapting the software for our custom PCB I need to make some changes in some devicetree nodes for the net core. Therefore I wanted to add...
I designed a circuit using the NRF54 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK . The code can be...
Just bringing this to your attention. This has been an issue since at least 2.6.1, and appears to still be a problem in main.
static void connected(struct bt_conn...
Hi, What specific steps must be followed to modify the charging current (BCHGISET) of the nPM1304? The information I found says to disable the charger first (set BCHGENABLECLR...
I am evaluating the monitor mode debugging support in nRF Connect SDK with nRF52840-DK and an arbitrary BLE sample (like peripheral_uart). My SDK/toolchain version is 3.1...
Summary
We are running on an nRF54L15 and receiving continuous NMEA output from a GNSS module over UART using UART ASYNC. After some time (30 minutes to hours) of normal...
Hello,
I am getting an error with the modem_info_params_get() function when I try to get the modem parameters. I am currently using SDK 3.2.0 with the FW MFW_nRF9151-NTN_v1...
Board: nRF54L15-DK (PCA10156), hardware version 1.0.0 OS tested: Windows (Lenovo Legion 5), also tested on Linux — same result on both
Problem
The board is not recognized...
Hi, I am trying to sound two reflectors from a single initiator, and since the CS works on a one-to-one ACL system, I wanted to know how I can reset the CS-related stuff in...
Hello,
On my board I implemented an RS-485 interface using the ST4E1216IDT transceiver. The DE (Driver Enable) and RE (Receiver Enable) pins are tied together and connected...
