Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello!
I am hitting a really frustrating issue running Zephyr on a XIAO BLE Sense module which is based on the nRF52840 MCU. I am simply trying to verify development setup...
Hello,
On a pairing failure from iOS (either cancel or timeout of the pairing dialog alert "Bluetooth Pairing Request"), the device no longer allows pairing until a software...
Recently our firmware team encountered a new version of NRF52840 and our hardware team "orders the available chip". How can I know and manage the version when we design the...
I was wondering whether having GATT client and server in same chip (NRF52832) would work? If so, then how would I need to set up bt_conn_auth_cb on zephyr if both uses passkey...
Hi,my board is nRF52840dK,and the SDK is ncs 2.7.0.
I want to modify the subevent parameters,
Is there any API to modify them in my code but not in prj.conf? such as ...
The provisioner sample was used as the base code for adding the function to set model's publication address. After doing so the end node goes into
Requesting Help regarding...
I currently am using a nRF9160DK. I want to have the nrf52840 on it scan for BLE devices and return the device count and then send this over UART to the nrf9160.
How can...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
Hi,
I am working on a board combination of nrf52840 and HL7800 modem. So, I just migrated from 3.6.0 zephyr to 3.7.0 and ncs 2.7-branch.
modem driver: https://github.com...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
