If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
Is a Zigbee Direct SDK available for Linux which could be used to allow it to act as a Zigbee Virtual Device (ZVD) using Bluetooth LE?
I am particularly interested in the...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
“'\x03\x01\x00\xDB\xDC\x00\x00\xDB\xDD\xFF\xD5\xD1\xC0”An error occurred during the transfer of the bin file, and the packet was returned when the crc was fetched. What should...
Hi,
I'm using nRF52833 DK and SDK v17 to test my applications.
I have to use ADC on nRF52811 SoC, and I wanted to develop a demo on nRF52833DK before implementing on nRF52811...
I am trying BLE+WiFi coexistence on NCS 2.8.0 with nRF7002DK and finding some issues.
First is that it's non-functional. Running the wifi/ble_coex example, there is no...
Hello,
I have a BLE DFU question in this thread that has not yet been resolved.
Since the BLE DFU problem has not been resolved, I have implemented a USB DFU as an alternative...
Hi, I bougth 2 nrf52840 dongle but I dont't know how to use it or program them. So I tried to learn about it looking the getting started guide, this beginners tutorial and...
Hi All,
I have a few nRF9151 that don't want to boot.
I'm not sure if they ever had working modem firmware on them:
Any ideas on how to un-brick?
Thanks!
Ja...
HI,
I am using "NRF_POWER -> TASKS_CONSTLAT = 1 ;" to enable CONSTLAT, but when i printf("TASKS_CONSTLAT %d",NRF_POWER->CONSTLATSTAT); the result is still 0; how can i...
Hi,
I work on a BC805M module (nrF52805) with the sdk17.1.0 & S112. It is powered by a CR2450 battery.
I like to reduce the consumption of the ble_app_beacon exemple....
Hello,
I am using the nrf7002 ek and attempting to optimise the RAM assignment for the project. I have reduced the size of several thread stack sizes as well as the heap...
