Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi ,
I'm writing some code of mine , declaration functions all well defined and compilation no error or warning but only this 1 error at end of my code.
I'm using SDK...
To whom it may concern,
I am testing SPI Slave and I have an issue that I am not able to change the pin numbers in the peripheral configuration for SPIS0 and 1.
It works...
Hello,
we have developed a solar powered LED module with an additional battery. It is based on the nrf52832. The WDT and TWI is mainly used and for BLE the soft device...
Hi everybody,
I am developing a wireless interface on an nRF52840 chip (Laird BL654) and I do have a problem with the SDK integration in Keil uVision.When "Manag(ing) the...
Hi,
i have PCA10059 dongle board. when i want run my program on it, fds_init return FDS_ERR_NO_PAGES. and also in nrf connect i can see range of different application...
Due to the rewrite of the DSM persistent storage layer the DSM_VIRTUAL_ADDR_MAX define can no longer be set to 0. This has changed since 3.2.0 where it could be 0.
During...
I ask you for help with programming Bluetooth module u-blox ANNA-B112. It is based on nRF52832. I have already installed Keil MDK5 with nRF52832_xxAB package, soldered the...
I'm trying to use sine function such as: S = sin(0.8)
But variable S come to zero after this code. Go to Debug mode and add a break point to view the change of variable...
Hi,
can we do the mathematical operations (like math.sqrt ) using nRF51822 ? Since, our project requires many simple mathematical operations, we need to decide whether...
Hi,
During the initialization of the SIM I have this message:
There was an error submitting your user information. This SIM cannot be activated. I am from Israel. What...
Hi All,
I have the strange issue with scanning. I have the project losely based on examples where I created peripheral adevrtising with 1s interval. This sends the custom...
Hi there, I'm using nrfutil ( nrfutil version 6.0.1 ) to dfu via ble (dongle),
Mac (10.15.2), windows (10), linux (raspbian) have been tried out to update the firmware none...
I am using the '840 to construct a small network using the ESB stack. In this design, a master (dongle) transmits to each slave and receives an ACK w/payload response. The...
