Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi ,
can u please provide more details about error code 4, returned by ble_ancs_c_init function.
what is this error, and how to resolve it???
thanks,
amarjeet
Hi there,
we are developing an application based on simple IEEE 802.15.4 packets, for which we use the radio peripheral. Every example found in the SDK starts with switching...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
Hello everyone,
I am developing a ble device and cant get under 7mA.
For test i used example application. BLE Beacon example. And the hardware part is realy basic. Only...
Hi,
We need to design a network with one master and 36 devices connected, with "long range" capability, exchanging sometime messages from 100 to 4000 bytes.
The number...
I understand from forum post https://devzone.nordicsemi.com/f/nordic-q-a/19250/the-number-of-central-connections-in-s140 that S140 v5.0.0 1.alpha release supports 8 concurrent...
I understand that Nordic provides a proprietary DFU via the BLE mesh. What mechanisms are in place to ensure that all packets reach their destination, e.g. acknowledgements...
-Using SoftDevice S110 8.0.0 for the nRF51822_xxAA.
-UART0 running on 19k2 without flow control (only rx/tx) and using irq priority APP_IRQ_PRIORITY_LOW (=3)
-Using the...
I'm currently porting my code from nrf52832/S132 to nrf52810/S112 (SDK14.2).
It seems that the s112 has no support for scanning, i.e., BLE_GAP_EVT_ADV_REPORT, sd_ble_gap_scan_start...
Hi,
I am working with the 52832, writing values on the flash and I'd like to make sure that I have done it correctly, the correct values are where they should be.
Is there...
Regarding range through human body, is bluetooth 5 coming with real improvements ? Can anyone testify ? for example, for a sensor behind the torso in the middle of the line...
Hi All,
I have been busy trying to get my application programmed onto my NRF52 dongle by using the Nordic NRF52 DK board as a Segger debug/programming interface. All was...
I want to design NRF52832 with 2.5 VDD and connect to an UART IC (CP2012),
unfortunately, "CP2012" just work in minimal 3.0V.
So, here is the question,
When NRF52832...
Hi,
I have recently tested some commands from the radio test example given in the following link using a PredevKit for the nRF52840 and it was quite fine:
http://infocenter...
