Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi Nordic,
I'm looking at the PM_EVT_FLASH_GARBAGE_COLLECTED event in SDK14.2 and have noticed that it is generated even if garbage collection fails. Currently no error...
On SDK 14.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
We are using SoftDevice: sd132 v 5.0.
With event "BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST", the function "sd_ble_gatts_exchange_mtu_reply" always return with "NRF_ERROR_INVALID_STATE...
I am using Fansttel BT832X SoC with SDK 14.2 ( Soft Device Version S132 5.0 ). i have configured PA/LNA mode in BT832X module. If i use only BLE advertisement i can see the...
Hi,
We want to update nrf52832 via uart. We have host controller and want to upgrade nrf52832 through it. We have SDK BLE_2.0.1 for the mesh. I had gone through DFU Example...
Hey,
I have a smart kettle Redmond RK-g201s, which is controlled by bluetooth. I have read that it has nrf51 SoC. It has 1 service with 2 characteristics: for read and for...
Hi Nordic:
I want to consult one question about "BLE HID Keyboard". I am trying to use the product---nRF52832 to make the "BLE HID Keyboard".
Then I download the source...
Hello Nordic Team,
I have some issues with the PPK since i uptdated nrfconnect from 2.0 to 2.4.
I get this error message when I try to select the serial port on Power...
I have some working knowledge of Android but I'm new to Fragments, Injection, Binding, ButterKnife .etc. I have gone through some videos and tutorials but can't catch where...
Hi,
I am using the nRF52832 DK for connecting and collecting the data from multiple beacons simultaneously. Right now i use the nRF_Connect desktop application for collecting...
Hi,
We have a nRF51822 project based on ble_app_hids_keyboard, SDK 12.3. When using Keil, it runs well. However, when using arm-gcc to compile the same code, something wrong...
Hi,
I am currently exploring the USB_CDC_ACM examples as well as the NFC record launch app.
Individually, I can make the examples run fine.
Then, I tried to combine...
Using nRF52840 SDK 15.0.0 with SoftDevice
I am trying to protect the Access Port, used to do it using the following command
nrf_nvmc_write_word(NRF_UICR->APPROTECT, 0xFFFFFF00...
Hi,
I'm using the NRF52840 SDK version V15. My program uses:
1. softdevice (BLE communication)
2. SPI uses using SPIM interface in nonblocking mode.
3. Timer event...
