I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello,
I am trying to see how the signal strength for Zigbee and BLE changes when the distance between two nR5340 DK increases.
I used central_uart and peripheral_uart...
Although my Googling skills are not the best I have, so far, been unable to find any examples or driver documentation for the comparator peripheral of the nRF52840 for the...
I'm using the asset_tracker app on a custom board and have built 50 of the custom boards. All but one of them start the modem and listen to the LTE receiver for a full minute...
Hello, I followed getting starting guide, and got SDK and tools installed for nRF52-DK, I'm trying to open, build and run some examples. But when trying to open any example...
Hi.
I am using nRF52840 dongle and running saadc example on it.
To print the ADC data buffer "p_event->data.done.p_buffer" in PC, I am using USB_CDC. The size of SAMPLES_IN_BUFFER...
I have implemented the custom service and added custom characteristics following the tutorial series, now I can connect and see the characteristics and their values. I can...
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
Hello
I'm asking a question because there's a part that doesn't work well while using ble_nus_data_send().
There is a problem sending continuous data to the app using...
Hello
Sorry this is a basic question and I shouldn't be bothering you with this but I have already dealt with a number of issues with Segger so I couldn't resist. - I have...
