My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
I am new to IoT development, and am working with the Nordic Thingy:91, and nRF9160 development kit as a starting point for development. Is there a preferred operating system...
Hello,
im using nrf52840 with sd140 and sdk17.0.1
in my project i have implemented a libuarte communication that works well usually, but rarely, and usually after days...
Device Name : nRF52840-DK PCA10056
I have 4 questions listed below, the reason is Instead of creating multiple ticket/case we can follow up using the same ticket to avoid...
Hi! Thanks for reading this post. I'm having an issue creating a firmware package for our manufacturer. I'm using a nRF52832 with SDK version 15.3.0_59ac345. Whenever I merge...
I have a question about the baud rate of the UART. I have set the baud rate of the UART to 19200bps, but can it work without a problem even if there is a percentage difference...
Hello,
I have trouble to create a project on NRF9160 DK.
I follow all the steps on getting starting guide and i also check all the steps on getting starting assistant...
Hi Team,
Nrf52840 DK acting as central and we trying to connect our peripheral device, we observed below logs with total duration of around 300ms.
Is there any way limit...
Hi forum,
I am working on nrf52832 using sdk15.0.0. using project ble_app_beacon.
In this project I am setting tx_power 0dbm,4dbm,-4dbm and -8dbm.while setting this tx_power...
Hi, Nordic
nRF52 as GZP Device, nRF24 as GZP Host
I know if nRF52 is range of nRF24, the pair will be worked.
I want to know what is the distance.
And if I use unencrypt...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
Hi
I want to receive data through UART RX interrupt.
--> A n interruption occurs to notify me w hen one character(byte) is received, and i store it to my memory buffer...
