I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
Hi,
For example ble_app_uart, when the peripheral ble rx buffer is almost full, I want to control the central write with response, but I don't konw how to indicate the central...
When evulating the nrf5340 for one of our projects, two questions came up regarding some of the security features used to mitigate tampering and malicious code:
What is...
Hi
sir we have nrf9160-dk and planning to interface some sensors to it but the issue we are facing is that the gpios are at 1.8v where as we need 3.3v logics to interface...
Hello everyone,
I getting stocked now for 1,5 days to get the nRF-Connected SDK running
I am using macOSCatalina 10.15.7
segger 5.20
Nordic SDK Tag v1.4.0
using...
Hi Team,
I'm working on scanner and NCS/Zephyr bt_le_scan_start callback API
typedef void bt_le_scan_cb_t(const bt_addr_le_t *addr, int8_t rssi, uint8_t adv_type, struct...
Hi
I have implemented a custom DFU process, where NRF52840 sends another NRF52833 an image to program.
The NRF52833 receives the image and validates CRC, if all OK , I...
Hi,
I'm using a nrf52833 in may application.
I have 2 Identical units with bare nrf52833.
refer the unit as normal ad defective.
test a.
while flash a simple FW...
Hello ,
I am using NRF 52 DK 15.3.0 SDK and ble_free_rtos_hrs example , I want to have a feature to start and stop the advertisement ( by interrupt driven , task notify...
Hi Nordic..
currently we are going to implement serial bootloader dfu from other MCU (infineon chip).
We have create flasher from MCU to nrf52832 to do serial fw update...
Hi
I am using nrf52832 .i am trying to connect to a device using sd_ble_gap_connect but i am getting NRF_ERROR_INVALID_ADDR error.
i am modifying ble_app_cli to achieve...
Hello
I'm going to use J-link's virtual port to see the characters being printed.
I connected custom pcb to Vcc, Swdio, Swclk, Gnd pin and tx, rx pin of J-link.
And...
In our mesh application, we are trying to give all our devices the same network key. As we are planning to have in excess of 100,000 devices, the 2-byte unicast address is...
