Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
Hi
i m using Bmm150 magnetometer sensor. i m trying to read x y z values. However, im not able to obtain the correct magnetometer values. I'm getting 0000 as values in all...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
PLease, could anyone provide me a code exaple on which i can learn how to use sd_flash_write & sd_flash_erease ? I tried to use them but keil give me this : .\_build\nrf51822_xxac...
Hello Dev Zone.
thanks for watching mt ask.
I need help.
I have 2 question.
1. I need use saadc continuous sampling
in SDK example, is it continuous Mode?
...
For RAM locations, I've looked at the getting started guide that discusses using debugging to find the RAM address. https://devzone.nordicsemi.com/nordic/short-range-guides...
I know one of nRF52840 SPI instances supports direct DCX signal drive but I can't seem to find any mention to this feature in nRF52832 so I am assuming none of its instances...
Hi Sir,
As check the ref. schematic of CKAA, the pin count shows 94.
But in the below table shows the pin count is 93
Is there a typo in the datasheet (V1.1)?
...
We are using nrf52832 and S132 Softdevice. The app starts from 0x26000 and we want to change to some other location may be from 0x27000. We could see that SD is using the...
Hello !
is possible turn off my system using sd_power_system_off when the Watch dog is enabled?
After I called sd_power_system_off my device is restarting and initialize...
I can not find where to change the default pins to connect the nrf52840 to the rpi over SPI. The default pins are SPI pin Raspberry Pi pin nRF52833, nRF52840 or nRF52811 pin...
I have begun using V1.2.0
It seems that I'm no longer to enter AT commands.
I've also tried the AT Command sample and get the same issue.
No problem connecting through...
Hello,
I am adapting the 802.15.4 wireless UART example from the nRF5 SDK 15.3 to also make scans and associate with a PAN coordinator. However i am having trouble with...
I have a time-sensitive block of code run purely by the CPU, not within any interrupt handler or peripheral. Part of the execution is getting interrupted, and so what I would...
I am testing DA7212 with my nrf52840 and i have made connections but i am not sure if thats right. Also i am trying to use i2s loopback example from sdk.
i need some gu...
