Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
I am trying make some temperature sensor with Segger and nRF52 based on Mesh BLE v4.0.
Currently I am researching documentation and examples to pick best solution...
I'm trying to use the information from this devpost: https://devzone.nordicsemi.com/f/nordic-q-a/39629/how-to-send-data-to-all-node-over-mesh
However, my remaining questions...
I would like to see an example or documentation about how to set my nRF52 DK into various sleep modes. I know that calling "sd_power_system_off()" will turn the device into...
Hello how are you?
I don't speak English very well but I have a doubt about using mesh and nfc simultaneously.
I'm using the Nordic-Thingy52-mesh-demo example - (Nordic...
Hi, team
I am using nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_ancs_c sample application. and i wnated to add extra notification attribute.
added BLE_ANCS_KEY1...
As I understand from documentation current limit for nRF PPK is 70mA. This is when PPK automatically sets measurement range from 1 o 70mA. My question is: Is there a way to...
1、Demo position：Nordic\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart\pca10056
2、I find when the code execute the function of timer_start_op_schedule,the CRITICAL_REGION_ENTER...
Hello,
Using this link ( https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral ) I'm able to add passkey protection...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
