Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
I did not do mesh SDK for a long time. Now when I see SDK Mesh, I saw Low power Node example. It can run with Mesh network and update OTA by DFU buttonless (I don...
Hi,
I had an experience with embedded programming but never with wireless technology. I am using Nordic SDK v16.0.0 and nRF Mesh SDK v4.0.0.
Here is a short description...
Hello All,
I am working on the Nrf52810 board with sdk 14.2.
I have implemented the read ,write , delete feature in my code.
Now it is creating new entry for repeating...
Dear All, I am trying to compile an application based on the Zephyr project for the nrf52. I am following the instructions from here .
I am using Windows. Using SES everything...
Thanks in advance.
Hi guys am working with nrf5282 (softdevice s132 V1.6.0 and SDK version 15.2.0), also enabled freertos, and also make softdevice changes rleated freertos...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
As part of my Factory setup we want to download MBR, bootloader, SoftDevice...
Hi,
I would like to perform DFU over Mesh. I am following the steps
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v4.0.0/md_doc_libraries_dfu_dfu_quick_start...
Hi,
anyone help me.
I am facing the issue during DFU with OTA. the steps are listed which had I done,
here trying to update softdevice.
1. Erase all.
2.flashed softdevice...
hey guys,
I want to write a c code to display temperature sensor data which is inbuilt in the nrf52840. I am using segger embedded studio. Can I get some reference code...
SDK: 15.3.0
Softdevice: S140 6.1.1
Brief usage: multi protocol radio driver 1.5.0, uart1, spi1, twi1, saadc, ble, gpiote 2 inputs, pwm1
I have been finding high current...
Hi,
I'm running into issues with the watchdog never firing. I'm using SDK v15.3.0, with S132 v6.1.1, and a custom bootloader (based off secure_bootloader example).
The...
I can successfully download an image using nrfutil dfu serial when I use a test image compiling the bootloader with the Nordic default public key.
I cannot successfully...
Hi. Is it possible at all to link a GPS module to an nRF52840 SoC and being able to advertise coordinates without having to connect the nRF52840 to the remote node? Thank...
