Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everyone,
I am migrating my project from SDK 14.2 to SDK 15.3 and i am using nRF52832 on SES v4.12.
Before putting in a question, i went to the forums and checked and...
Softdevice : S132
SDK ver : 15.3.0
Board : MBN52832DK
Hi There,
i was trying to do the DFU Example (ref : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi,
I am using nrf52840 dongle and tried to program it with the example that was provided with sdk15. I programmed it with ble_app_bps, it successfully paired with my...
Hi there,
I'm working on a BLE project using the nRF52832 and am having trouble implementing flash storage. I'm using SDK 132 v6.1.1, and the flash storage library to save...
I am implementing the Device Information Service, and want to include the bootloader version as "Firmware revision" in DIS and the application version as "Software revision...
I am new to nordic ble chips.
I am using nrf52832 ble chip, s132_nrf52_3.0.0_softdevice
I am trying to update firmware on the air. But I am getting an error that I do not...
Hey,
Up until now I have only been dealing with software. Now however, I want to create a device that I can use to track my bike by GPS and heading. In the future, I want...
Hi
I am having a problem now(maybe a bug).I refer to nest_state.c and access.c build my user_flash.
But some time,when I reset device,write data to flah will be fail....
Hi,
I'm using the nrf52840 with sdk v15.3 and I'm trying to list of the characteristics of a specific service that has a 128 bit uuid running on a peripheral. However, even...
Hello,
I would like to be clear on the pros/cons of registering a new SIG-adopted UUID versus a vendor-specific UUID. We are a small developer and the cost of registering...
Hello,
I have two differents sensors on one SPI port and I don't really know how to be able to use both. Of course all are connected in the same MISO/MOSI/SCK but there...
Hello,
We currently have several devices out in the field as test units, installed at beta sites. The new modem firmware v1.1 has several features/fixes that we want to...
Hi, we are working on custom board using nRF52811 SOC, I have some confusion
1. regarding the antenna design, I copied the Antenna from Dev board, but it is designed for...
Hello,
There's an interest on the LTE-MTC module.
I can see it's based on nRF9160.
I'd like to inquire about the MTC technology please, does this module support CATM2...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
